Other Allied Equipments

Spindles ate used a device tor power transmission and are placed between Couplings.

Spindles are manufactured out of forged steel, basically EN-8 or EN-9 and are property machined as per the design and requirement.

Plate bending machine is used for bending the plates in round shape in the cold form. We manufacture Mechanical and hydraulic plate bending machines for MS Plates.

The current maximum capacity machine is of upto 32mm with 3000mm width.

As we all are aware that approximately 5% material is left back in the form of slag in Induction/Arc Melting Furnace Pots. Till today, the Furnace owner have been paying something from their pocket to lift Slag from their works and dispose it off. This Slag included around 15% of Steel Scrap Chips, which were extracted by breaking the Slag manually through hammers & separating the chips left wasted with Slag. In the present Scenario of Economic Competence how can one think of such handsome losses, which can be recovered easily?

SMT is pleased to introduce a semi-automatic system ot crushing the Waste Steel Scrap Chips (Slag) in the form of small grains. It consists of removing dust from these grains and then separating the chips by means of magnetic chips separating machines. Finally, these chips are meshed in ball mill, which assure that not even a single chip of steel is left behind in the slag.

Discharging Ejector is an Electro-mechanical device which is used to expel the hot material from the re-heating furnace to the Rolling Mill. It has a Mill Housing Type structure with a movable frame and can do both front and side travel for discharging of Hot Material (like Ingots. Billets) from re-heating furnace.

It comes complete with heavy stands, rollers, cooling system, wheels for cross travel, gear box and pushing arrangements etc., it uses a square billet of approx. 6 meter (or more) length as the device to push the hot material out of the re-heating furnace.

It is manufactured depending on the size and capacity of the re-heating furnace.

A Mechanical Pusher is an Electro-Mechanical or Hydraulic device which is used for feeding or charging of raw material (like ingots, billets etc) into the reheating furnace.

Various components which are used in the manufacturing of a Charging pusher are: Heavy steel slab frame, pushing screw with pushing slab, multi stage type reduction gear box or a hydraulic power pack with alloy steel shafts in case of a hydraulic pusher.

Depending on the raw material to be feed i.e. scrap / miss roll, ingots / billets or heavy blooms and their sizes, the mechanical or hydraulic type pusher is designed and supplied.

Twist Pipe & Roller guide box are installed at the entry and exit of the Mill Stand in Rolling Mill. They are used for guiding of symmetrical section such as Round. Oval, Square. Flat etc into Mill Stands for Rolling.

These are Stainless Steel Casted pipe and boxes which consist of precisely machined Body. Leaf, set of Guides, Nuts & Bolts and Pins & Roller Bearing. The water system for cooling the rolls of the guides is effectively designed and precisely machined in-order to get maximum cooling for the high Alloy Rolls

We manufacture all standard and custom size Twist Pipes & Roller Guide Boxes such as:

A Pulley is a power transmission cum speed controller device which can be used at various places depending on the application and size.

In Rolling Mills it is used between motor to flywheel and flywheel to gear box so as to control speed input speed as per the application. It is duly machined and balanced and comes in all groove sizes and bores. The material mostly used to manufacture the pulley is Graded Cast Iron. We make pulleys from 150 mm o 3500 mm Dia.

It comes complete with Shaft, bearings. Plummer Blocks. Base Plates and Foundation Bolts etc.. and is designed and manufactured as per the application.

Billet Grabber is a mechanical device used in Steel Melting Shops for grabbing the Ingots / Billets. It helps in properly placing the finished goods in stock yard. It is very safe to use and has very effective results.

It is not a magnetic, hydraulic, electronic or pneumatic device. It is a pure mechanical device and has a number of advantages over other material lifting equipments. With a fully reliable and a total mechanical interlocking system it can help save a lot of time and resources and hence result in the increased productivity by many folds.

It comes in various sizes and capacities.

Oil Lubrication systems are used to maintain regular supply of ambience temperature oil to mating parts of Gear Boxes in Rolling Mill.

Oil Lubrication Unit is a Pit Hole type box, fabricated out of M.S. plate body and comes complete with all the accessories like: Oil Reservoir. Heat Exchanger, Oil Strainer, Contact Thermometer / Manometer, Duplex Fitter, Pressure Gauge. Pressure / Flow Switch. Inlet & Outlet nozzles, lubricating pump unit, Complete Pipeline to & from the Gear Boxes. Complete with the Control Panel.

The system is so designed that the lubricant flows back to the reservoir under the influence of gravity. We manufacture all standard and custom size oil lubrication systems based on the LPM etc.